Jump to content
FrankM

Earthworm electrical current sensitivity

Recommended Posts

I read an article that discussed a Japanese physicists observations about earthworms exiting the ground before one of their big earthquakes.

 

http://animalsandearthquakes.com/ikeya.htm

 

Electric currents have been used for earthworm extraction going back many decades (worm getters), but I could not find any studies where their sensitivity to specific currents levels was measured.

 

I have raised garden beds which are prolific with earthworms so I decided to see if I could get them to respond with fairly low electric currents. I used #12 solid copper wire as electrodes, starting out with 6" length and then later making some 12". I started out with a 38.6 VDC source, an old HP printer transformer, the 6" electrodes vertically in the ground and 10" spacing, this giving me approximately 60 ma no matter where I inserted the electrodes in the garden bed.

 

I had multiple worms exiting the ground within 60 seconds (worms move slow). I changed the spacing to 16" (to a fresh area) and the current was just a few milliamps lower, and the same worm extraction experience was noted.

 

The next day I used two different transformers, a 12 VDC and a 9 VAC and experimented with the spacing. The current at 12 VDC was about 20 ma and that for the 9 VAC, approx. 15 ma current. There was a slight difference between worm exit counts and size AC vs DC, but the current was slightly different.

 

The following day I prepared the longer electrodes, 12", and experimented with various spacings, AC and DC (both 12 and 38 V). I also prepared a 13" insulated electrode where only 1" was exposed and inserted that into the ground so that the current had a somewhat vertical component. The number of worms exiting varied somewhat with the applied current, which depended upon electrode size and insertion depth. In the maximum current area I suspect worms were immobilized, but this is conjecture only because of where I observed worms exiting relative to the electrodes.

 

I did not determine the minimum current at which worms would exit the ground but I could get exiting with a little as 3 ma between electrodes, which means the actual current differential experienced by the worms has to be in the sub-milliamp range.

 

I can conclude the earthworms will exit the ground if there is a sustained current. Worms don't move fast, thus they probably started toward the surface as soon as they experienced a current level that was uncomfortable to them. I also had small garden centipedes (beneficials) exiting from the ground in the same area as the worms, thus they were being irritated by the same in-ground currents as the worms.

 

There were a number of peculiarities noted in where the worms exited relative to the electrodes but more studies are needed with better controls to see if these peculiarities are significant. I also placed some of the worms that had exited and moved away from the current influence directly in between the electrodes and watched their reaction. Size seems to matter, and if they couldn't exit immediately from the area of maximum current influence they had problems. The next day I used multiple electrode configurations and switching the polarity of inner and outer electrodes, this to examine if worms have a polarity sensitivity.

 

From what is known, the earth currents generated before and during earthquakes are more a DC type with variations in magnitude, it is not sinusoidal with plus and minus swings.

Share this post


Link to post
Share on other sites

Great study, FrankM. That is a substantial amount of current at this scale. I don't know much else about the situation other than that you are grounding current into the local earth. I had wondered about surface/air changes in electric field but this discussion speaks to response from "creatures of length" to lateral distributions.

Share this post


Link to post
Share on other sites

I don't know the actual current across the worms body. I did find that there are two types of worms, those that burrow vertically and those that burrow horizontally, and I do not know which type(s) I have. I did observe some worms exiting vertically but I don't know if that has anything to do with the manner in which they burrow.

 

I don't have a video camera, which would have allowed me to record and replay the worm exits to get counts and their exit points relative to the positive and negative terminals, there seems to be a slight difference. One really needs something like a variac or a variable resistance to adjust the current to a consistent value when the electrodes are moved to fresh areas. I tried to be consistent in the depth I inserted the electrodes but slight variations are inevitable.

 

The actual in-ground current vectors created by seismic action will be different than what one gets from two rather close space electrodes, but I know that earthworms will respond to relatively low seismic generated currents. At the near surface I would expect the current vectors to be mainly horizontal. One would think the worms original orientation to the current vector would be a factor in how much potential would be across their bodies. I do not have any instruments that would be suitable for measuring the electrical resistance of a worms body, just in case anyone is curious about that.

 

What we really need to know is the range of currents that can be expected from seismic events. I have already concluded worms will respond to relatively low current levels, and it requires a period of applied current to stimulate worms to exit from the ground. Now, how can this knowledge be used to detect seismic generated currents?

Share this post


Link to post
Share on other sites

First of all, I apologize for reviving such an old thread, I recently got into fishing, and one of the recommended videos on youtube would always come up about electricity worm getters, now i've made my own attempt just last night after weeks of theorizing. I have failed, despite my search on the internet, not much result came up on the subject of earth worm and electricity sensitivity. I said to myself, people have better things to do than to test how sensitive organisms are to electricity. therefore, I turned my attention to this experiment.

 

From what I've read and seen, most people use household 120v to shock the ground, and I also discovered there had been commercialized products that used the same principle, however there were too many accidents and they had to discontinue the product. My attempt was made with safety in mind.

 

First I started off with a car battery that was fully charged, I then had 2 metal alloy bolts 12" long with about .5 ohms and stuck them in a moist grass patch that i watered down. I used booster cables to connect the battery to the two rods and started measuring. to my surprise, the earth around had a minimum of .5 v to 8 v depending on the distance between the the probes on the multimeter and the two bolts. there were no measurable current between any components on the circuit. The result didn't change much after I applied battery charger that gave off an current at 15v and 3.5 amps. No worms after 30 minutes, I then gave up.

 

I have minimum understanding of resistance vs current and the potential difference. If anyone or OP can offer some insight, it would help me rest my mind.

 

My next attempt will be in the rain, with the same equipment, and if that doesn't work, I'll move on to the 120v.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.