jordehwa

I figured it out. I made the mistake of connecting my distilling apparatus with rubber stoppers. So I'm guessing there must be small bits of rubber dissolved in my ethyl acetate.

Does anyone know if activated charcoal will clean the dissolved rubber out of my ethyl acetate?

Yes. Before distillation it was clear and left a film, after it was yellow and left a film.

Anything?

I bought some M.E.K. substitute from home depot since I read on the MSDS that it was 100% Ethyl Acetate. So I did an evaporation test on some glass and it left a film so I decided to distill it just in case. Anyway the ethyl acetate was clear when I started now its slightly yellowish and still leaves a film. What makes it yellow and should it concern me? Also is the film normal?

Thanks.

Air drying for the most part should be fine for me. But lets just say for example I was distilling pure acetone, and then right after that I started to distill pure ethanol (again this is just for example) how many ml of the ethanol distillate should I let run through the condenser until it would be fully rinsed? by the way my Graham condenser is 300 mms long.

Thanks again.

Hi I just bought my first condenser, its a Graham condenser. I did some simple distillation and It worked well.

I just was wondering what is the best way to dry out the inner coil?

Thanks.

so i was thinking about how NaCl is edible and very simple to make. So what i was wondering is if you guys know of any simple synthesis experiments to make edible compounds. Thanks.

yeah thanks i will make sure the crystals are dry and pure before tasting it.

So i know that Sodium bicarbonate (NaHCO3) + Hydrochloric acid (HCl) ==> Sodium chloride (NaCl). So what i want to do is make some crystalize it and see if it tastes better or different then normal table salt. It seems to me like this would be safe to do but just to be sure would tasting homemade salt be ok?

Thanks by the way i do have experience HCl.

Ok thanks for the ideas

Ok thanks i will try that.

Also is there anything that can be made with alcohols and HCl? I'm asking cuz alcohol is cheap and i have lots of HCl

Hi i love inorganic chemistry and have been doing it for a while. But i'm starting to get interested in organic chemistry, I just dont know were to start i dont have any advanced glassware or stuff like that. So can some post some simple organic chemistry experiments for me to do? Thanks

what i want to know is can a person (Me) from the U.S synthesize and sell chemicals on Ebay to others in the U.S legally without a permit?

Not dangerous chemicals like acids, but chemicals like copper sulphate , copper carbonate, manganese chloride and stuff like that?

The reason for me asking is its my hobby to synthesize chemicals, so i wanted to know if i could sell them on Ebay for a little extra money.

i put some copper wire in it and it dissolved to a light blue solution so i do think its nitric acid.

Hi i have been trying to make nitric acid, and i have some questions to make sure it really is nitric acid i have made.

here is what i did. Put 80 grams ammonium nitrate, 37 grams of copper, 50ml water and 100ml HCL into flask with a stopper and a tube in it so i could bubble NO2

into 50 ml of cold 3% H2O2. after i heated the flask by putting it into hot water it started bubbling.

It is strange to me the gas in the tube never looked brown or red like NO2, why is this?

also when it was finally done done bubbling i poured what i think should be nitric acid into a beaker, and it is bubbling like carbonated water, why? what is bubbling out?

So is this really nitric acid ?

thanks for the reply.

I still want to do some more reasearch on this. I'm not in college, I'm in home school so is there a website where I can do some more reasearch on this subject?

By the way whats this kind of problem called in chemistry?

So i my question is, How can I calculate how much acid is needed to fully react with a metal or compound, instead of just using excess acid?

For example like if you needed to dissolve 10 grams of zinc how could you calculate how much hcl is needed, so you dont ad too little or too much acid?

Please give me an example and explain. Thanks B)

Well i still have more MnO2 Just not very much only 2.50 grams this is just a test experiment.

Thanks a lot guys I will let you know how it goes.

So i want to make some Manganese(II) Chloride From MnO2 and HCL, yes I realize that this makes chlorine.

So i dissolved the MnO2 in the hcl and it has green Iron impurities in it, to much for recrystalaltion to work. what would be the best way to get the impurities out?

I am betting that your dig will encounter ground water way before you hit 100 feet much less 1000 feet.

Yeah I was just thinking about that after i posted. Well I might not be able to dig deep, I should be able to make some cool tunnals.

I totally rethought my tunnal. Here are the plans I drew with my computer. The white lines are vents made with PVC pipe.

If you guys want you could draw up your ideas.

This may seem weird to you guys but i have always wanted to do this as a kid. So here is my plan on digging a really deep hole, I might not make it to a 1000 feet but i want to dig as deep as i can, maybe even deeper than a 1000 feet.

I will add some vents, and maybe rest rooms or rooms to put digging tools in. I dont plan on digging straight down, but kind of at an angle. I will reinforce the walls and ceiling, so it dont cave in

If anyone has any tips or suggestions it would be greatly appreciated, like how will i make vents? and how will i get the dirt out when im hundreds of feet deep?

I want to know if any one else has tried anything like this? What kind of soils will I be digging in? and at what depths? What kind of stuff could i find?

By the way i live in central Minnesota. Thanks and please reply i still need lots of tips and suggestions. its a work in progress

even if the lithium oxides in air wouldn't the oxide also dissolve in an acid?

how would you do it?

so boric acid will make borates but you can also precipitate tetraborates with borax what the difference?

Synthesis of hydrobromic acid with sodium bromide and phosphoric acid.

And synthesis hydroiodic acid with potassium iodide and phosphoric acid.

i was wondering how well do these to experiments work? and is there a good way to do them?

ps: i know that these projects deal with very corrosive acids and toxic gases