Jump to content

Seeking Instruction Manual


studiot

Recommended Posts

Transistor Tester Integrated Circuit IC Tester Meter MOS PNP NPN Detector A9A6

 

https://picclick.com/1pc-Transistor-Tester-Detect-IC-Tester-Meter-Maintenance-262883524250.html

 

This is a you tube link I think but my internet cafe is too slow to show it.
The panel has 5 buttons are on the left, right, bottom, and Enter keys.
The next key is used to adjust the directory and change the model number, the or so key to move around the cursor options to change.The Enter key for the switch machine and execute the test command.Gently open the battery cover, add a 9V laminated battery, and then close the battery cover.Press Enter for more than 2 seconds can boot, boot automatically display the current battery voltage, when the voltage is lower than 7.5, please replace the battery, the low voltage will affect the reliability of the test result and protection automatic shutdown.
Boot: Enter key press 2 seconds then boot.
Shutdown: 1 in the OFF directory, press Enter button to immediately shutdown.
2 in any directory, press Enter button for more than 10 seconds then off.
3 in no operation after 60 seconds, automatic shutdown

 

Methods of devices placed:
1, the top of the chip alignment
2, put the most left transistor three slot
3, a 13 foot alignment IC Optocoupler
4, voltage regulator tubes placed IC block 13 and 14 feet.
Note: the transistor display pin order from left to right and the corresponding IC block, 10 feet, 11 feet, 12 feet
QQ622A56FE20130311105305_zpsad904c71.jpg

catalogue

 

function

 

Search

 

Auto mode

 

Device search , the unknown model chip inserted in ic seat can automatically identify the part number
( Automatic identification without input) ( other directories are auto- mode )

 

5.0v mode

 

3.3v mode

 

74HC

 

74HC series of logic device test (of the same, and 74LS series base drive level (different) need to manually enter the model)

 

74LS

 

74LS series of logic device test (of the same, and 74HC series base drive level (different) need to manually enter the model)

 

CD40

 

CD4000 series of logic device test (different, and HEF40 series base drive level (the same) need to manually enter the model)

 

HEF40

 

HEF4000 series of logic device test (different, and CD40 series base drive level (the same) need to manually enter the model)

 

45/145

 

45 series 145 series logic device test (the need to manually enter the model)

 

OTHER

 

Interface drive device testing, such as: MAX232, MAX485, 75175, 75176, 75c11.. (the need to manually select the model)

 

AMP

 

Operational amplifier, comparator class testing, such as: LM324, LM358, LM339, LM393, LM2902...(the need to manually enter the model).

 

TR

 

Transistor identification , and automatically determine the transistor types and pin order . Identifiable NPN , PNP, transistors , N- MOS , P -MOS way thyristor , triac , common anode common cathode rectifier automatic identification without input )

 

ZD

 

Zener regulator value test , test regulator regulator 0v-50v range accuracy 0.01v automatic identification without the need to enter

 

LIGHT

 

Optocoupler secondary the saturation voltage test , can test the the ordinary 4 feet optocoupler secondary saturation voltage automatic identification without input )

 

OFF

 

Shutdown

 

 

 

prompt

 

explanation

 

OK

 

Tests are normal

 

Batter

 

Battery voltage

 

Not found

 

Can?t find

 

Fault

 

The chip damaged or type mismatch

 

Open

 

Open circuit

 

Not supported

 

nonsupport

 

NPN

 

Triode

 

PNP

 

Triode

 

N-MOS

 

FET

 

P-MOS

 

FET

 

1-SCR

 

Way SCR

 

2-SCR

 

Triac

 

2D

 

Common cathode and common anode rectifier

 

A?k?b?c?e?g?

 

Specific pin

 

Out of range

 

Zener voltage beyond the scope

 

ERR1?2

 

Self-test failure

 

I hope the above Helps

 

Thanks Andy

Edited by Handy andy
Link to comment
Share on other sites

Thanks andy for finding a working video. +1

 

The video linked on the seller's site didn't work.

 

The written text instructions are worse than a joke.

 

5 buttons - I count 7

 

Long screed about fitting a 9 volt battery

 

As the video says, it uses two AA batteries.

 

Hold enter down for off.

 

No it has an off switch.

 

"put most left transistor three slot"

 

Your guess is as good as mine.

 

 

 

***************************************************

 

Well the instrument has arrived and mostly works as described by the guy in the vid, but it didn't recognise a 741.

 

Correctly identified a 2N5401 pnp transistor type and pinout.

 

Correctly identified CMOS 4001 gate chip.

 

Thanks everybody else for suggestions, keep them coming.

 

 

It could be a very useful gadget with some reliable instructions.

Link to comment
Share on other sites

Maybe this is too obvious a 741 is an "analogue" operational amplifier, not intended for "digital" operation perhaps that is why it wasn't recognized. The 741 is not programmable other than by using external passive circuit components.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.